The TGX20 from Dynacord is a 4-channel 5000W DSP power amplifier for live applications.
Dynacord TGX20 Features
- 4-channel DSP amplifier for live applications
- Market-leading power density with up to 20kW in 2RU
- Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
- OMNEO integration for seamless compatibility with Dante and OCA
- Full color touch screen for control without software
- TGX20 4-channel 5000W DSP power amplifier1
- Max. Output Power All Channels Driven
- 2Ω: 5200W
- 2.7Ω: 6000W
- 4Ω: 5000W
- 8Ω: 2500W
- Amplifier Channels4
- Max. Output Voltage210V peak
- Max. Output Current84A peak
- Amplifier
- Voltage Gain ref.1 kHz: 32.0 dB, adjustable 24-40 dB
- Input Sensitivity ref. to Max. Output Voltage: 13.7 dBu (3.73 V), adjustable 5.7-21.7 dBu
- THD 3 dB below Max., AES17, 1 kHz: < 0.05 %
- IMD-SMPTE, 60 Hz, 7 kHz: < 0.15 %
- DIM100, 3.15 kHz, 15 kHz: < 0.15 %
- Crosstalk ref. 1 kHz, 12 dB below Max., 8 Ω: < -80 dB
- Frequency Response ref. 1 kHz, analog in to speaker out: 20 Hz to 20 kHz (±1 dB)
- Damping Factor, 20 Hz to 200 Hz, 8 Ω: > 400
- Output Stage Topology: Class D, fixed frequency
- Signal to Noise Ratio
- A-Weighted, analog input: 115dB
- A-Weighted, digital input: 118dB
- Output Noise
- A-Weighted, analog input: < -70 dBu
- A-Weighted, digital input: < -73 dBu
- Digital Signal Processing
- Sampling Rate: 48 kHz/96 kHz, OMNEO/Dante synchronized
- Signal Delay/Latency
- Analog in to Speaker Out, 48 kHz/96 kHz: 0.70 ms/0.53 ms
- AES3 in to Speaker Out, 48 kHz/96 kHz: 1.00 ms/0.66 ms
- Dante Network Latency: typ. 1.00 ms
- Signal Processing: 32/40 bit, floating point
- User EQ: 12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type
- User Delay: 0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet)
- Array EQ: 5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass
- Array Delay: 0 to 500 ms per channel (units: μs, ms, s, cm, m, inches, feet)
- Speaker EQ: 10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass
- Speaker X-Over: Hi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; AlignmentDelay, 0 to 20 ms per channel
- Speaker FIR: up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
- Speaker Limiters: Peak Anticipation Limiter & RMS/TEMP Limiter per channel
- Other Functions: Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring
- Memory
- DSP Presets: 1 Factory + 20 User
- Speaker-Pool Presets: 30 speaker settings
- Source Supervision & Fallback: AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection
- Connectivity
- Analog Audio Input/Thru
- Type: 4 x 3-pin XLR female/male
- Max. Input Level: +24 dBu
- Input Impedance, active balanced: 20 kΩ
- Reference level equal to digital input: +21 dBu for 0 dBFS
- Digital Audio Input/Thru
- Type: 2 x 3-pin XLR (alternative use of Analog In/Thru)
- Format: AES3 (AES/EBU)
- Input Sample Rates: 32 to 192 kHz, internal Sample-Rate-Converter
- Thru Connector: active buffered, direct bypass if device is unpowered
- Network
- Type: 2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY
- Format: 1000base-T/100base-TX, integrated switch
- Network Audio Inputs: 8 channels, 48/96 kHz, OMNEO/Dante format
- Network Audio Outputs (Monitor): 2 channels, 48/96 kHz, OMNEO/Dante format
- Front side Service Port: 1 x USB Type A
- Mains Input: 1 x Neutrik powerCON-HC
- Speaker Output: 4 x NL4
- User Interface
- Display: 320 x 240 pixel, 3.5" color TFT"
- Front Panel Indicators: Full color LED illuminated ring
- Front Panel Operating Elements: Rotary encoder, Capacitive Touch Screen
- Rear Panel Indicators: 2 x LED (AES3 Input mode active, Amp-Find)
- Rear Panel Operating Elements: mains switch
- Power Requirements100 V to 240 V, 50 Hz to 60 Hz AC
- Power Consumption
- Rated Power Consumption: 2250 W
- ⅛ Maximum Output Power at 4 Ω: 2850 W
- Idle Mode (no input signal): 110 W
- Standby Mode: < 19 W
- Power Supply TopologySwitching Mode Power Supply with digital controlled Power Factor Correction
- ProtectionsAudio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, In rush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Under voltage Protection
- CoolingFront-to-rear, temperature controlled fans, supervised
- Ambient Temperature Limits40 °F to 105 °F (5 °C to 40 °C)
- IEC Protection ClassClass I (grounded)
- Electromagnetical EnvironmentE1, E2, E3
- Dimensions (WxHxD)19.02" x 3.47" x 20.24"
- Weight33 pounds
