The Williams AV IR SY23 D Dante Infrared Transmitter System is a commercial-grade, large-area Dante infrared system with IR+ transmitter, 2 emitters and array. Comes with Stethoset Receivers.
Williams AV IR SY23 D Features
- Commercial-grade
- Large-area Dante infrared system
- Includes IR+ transmitter, 2 emitters, and array
- Comes iwth Stethoset Receivers
- IR M1 D infrared modulator with Dante input1
- IR E4 emitters2
- IR A4 array1
- IR RX20 receivers5
- CHG 520 charger1
- IDP 008 ADA wall plaque1
- IR M1
- Dimensions: 19” (W) x 1.75” (H) x 8.2” (D) (48.3 cm x 4.5 cm x 20.8 cm)
- Weight: 5.2lb. (2.4 kg)
- Color: Black
- Rack Mount: Single Rack Unit
- Power Supply: International Desktop Supply
- Input: 36 W, 110-240 VAC 50-60 Hz
- Output: +48VDC, 0.75A center-positive
- Power Switch: Rocker switch with LED
- Signal to Noise Ratio: 67 dB (typical)
- Modulation: FM Wideband, +50kHz deviation, 50uS pre-emphasis
- Carrier Frequency: Selectable, 2.3/2.8 or 3.3/3.8MHz
- Frequency Response: 40 to 16,000Hz, +1 dB, -3dB, electrical response
- Total Harmonic Distortion: Less than 2%, electrical response
- Audio Processor Functions: DSP based; Compression 1:1, 1.5:1, or 2:1; High-pass and low-pass filter frequency control
- Auto Carrier Shut-Off: Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage.
- Infrared Test LED: Dual IR LED for receiver testing, monitoring, and audio signal testing.
- Audio Input: (2x) Combination 3-pin XLR, 1/4” (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power
- Dante: Optional
- Internal Test Tone: 400 Hz internal test tone selectable as audio input source for setup and diagnostics
- Remote Configuration: Available through embedded website
- Headphone Output: (2) 1/4″ headphone jacks on front panel for monitoring CH A and CH B audio inputs
- Emitter Output Jack: Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission.
- Operating requirements: 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere
- Approvals: CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
- Warranty: 2 years on Modulator, 90 days on accessories
- IR E4
- Dimensions: 7.5” (W) x 1.4” (H) x 3.6” (D) (19.1 cm x 3.6 cm x 9.1 cm)
- Weight: 0.8 lb (362 g)
- Color: Black
- Power: 48 VDC supplied by IR M1 via CAT 5e cable.
- Coverage Area: Up to 18,000 square feet in single channel mode
- Connectivity: +48VDC Power, RS-485 communication, and Baseband signals for IR trasmission are all provided via a single CAT5e cable inserted into an RJ-45 jack from the IR M1.
- Operating requirements: 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere
- Approvals: CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
- Warranty: 2 years on Emitter; 90 days on accessories
- IR A4
- Dimensions: 7.6"W x 6.6"D x 1.1"H (193mm x 168mm x 28mm)
- Weight: 2.4 lb (1100g)
- Color: Black
- Power: 48 VDC, 0.75A
- Connectivity: +48VDC Power, RS-485 communication, and Baseband signals for IR transmission are all provided via CAT5e cable(s) inserted into an RJ-45 jack from the IR M1 and out to the IR E4(s).
- Heat Dissipation: 1W
- Max Cable Length: 328 feet (100m)
- Plenum Rating: The IR A4 is not rated for use in plenum spaces and will need to be installed in a plenum box for use in such areas.
- Approvals: CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
- Warranty: 2 years
- IR RX20
- Weight: 1.6 oz
- Material and Color: IR Transparent polycarbonate, black
- Battery Type: LiPo
- Battery Life: 8 hours
- Battery Charger: CHG 520
- Operating Temp: 32-122° F (0-50° C)
- Range: Up to 15,000 sq. ft. in single channel mode with IR T2 transmitter
- Operating Frequency: 2.3 MHz or 2.8 MHz or stereo
- Frequency Response: 100 Hz to 12 kHz, ± 3 dB
- Signal to Noise Ratio: 60 dB at 10 m
- Controls: Volume control thumbwheel;3-position selection switch (2.3 MHz, 2.8 MHz, stereo), Off/on slider for power
- Acoustic Output: 120 dB MAX SSPL90 with 2 cc coupler
- Compatibility: Compatible with 2.3 MHz and 2.8 MHz IR transmitters
- Headphone Jack: 3.5mm stereo
- Ear pads: EAR 089
- Approvals: CE, RoHS, FCC, Canada, RCM, VCCI, WEEE
- Warranty: 5 years (90 days on battery)
- CHG 520
- Dimensions: 12″L x 6.25″W x 1.5″H (30.48 cm x 15.875 cm x 3.81 cm)
- Weight: 13.6 lbs
- Color: Black metal and plastic
- Power Supply Input: 120 VAC
- Power Supply: 100-240V / 12VDC TFP 043
- Unit Capacity: 5 Units
- Indicators: Individual Charging Indicators: Red LEDs
- Warranty: 1 year (90 day warranty on cables and power supply)
- Approvals: WEEE, RoHS, CE, FCC, CANADA, RCM, VCCI
- IDP 008 10-3/8" (L) x 6-¼" (W) x 1/8" (H)
