• Dynacord IPX10:8 DSP Power Amplifier
1 1

Dynacord IPX10:8 DSP Power Amplifier

Dynacord IPX10:8 DSP Power Amplifier

SoundPro Item: 11834 | Part Number: F.01U.329.715

$12,369.00
$12,369.00 $12,369.00
Your Price Sold out
MSRP: $12,369.00 | MAP: $12,369.00

Usually ships in 5-7 business days

  • 8 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply
  • Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
  • Dante and OCA integration via OMNEO with fallback options
  • Parallel, bridged and parallel-bridged drive modes with 70/100V/140V/200V and low impedance operation
  • High efficiency Eco Rail technology for lower operating costs
Log in or register for YOUR best price

Dynacord’s IPX10:8 is a dedicated amplifier for fixed install applications that require high power multichannel amplifiers with sophisticated speaker processing.

The IPX series from Dynacord, heard in stadiums, arenas, concert halls, and houses of worship, delivers high-power, multi channel amplification for fixed install applications with the added touch of sophisticated speaker processing. Featuring smart Eco Mode, digitally controlled interleaved PFC supply, comprehensive fallback options, and integrated DSP, the IPX series can run in 48 kHz or true 96 kHz (including FIR Drive). Operate each channel individually in low impedance mode or 70 V/ 100 V Direct Drive Mode, or bridge to 140 V/ 200 V Direct Drive for greater expansion to drive all kinds of loudspeakers. Besides analog inputs, Dante, and OCA via OMNEO, network inputs are available. Fully integrated with IRIS-NET, local control and supervision are simple with the front panel OLED display. The IPX Series streamlines the needs of your fixed install system.

View full details

Specifications

Dimensions
Dimensions (WxHxD)
19.02" x 3.47" x 20.24"
Electrical
Low-Z Mode, Max. Output Voltage
10.7 dBu (2.66 V), adjustable -1.3-22.7 dBu
THD (3 Db Below Max, AES17, 1 kHz)
<0.05%
Rated Power Consumption
1300W
Power Requirements
100 V to 240 V, 50 Hz to 60 Hz AC
Power Supply Topology
Switching Mode Power Supply with digital controlled Power Factor Correction
Audio
Frequency Response (ref. 1 Khz, Analog in to Speaker out)
20 Hz to 20 kHz (±0.5 dB)
Speaker Output
2 x 8-pin Euroblock, 6 mm, female
Connectivity
Output Stage Topology
Class D, fixed frequency
A-Weighted Analog Input
112dB
A-Weighted Digital Input
115dB
1/8 Max. Output Power at 4Ω
1780W
Idle Mode (no Input signal)
105W
Dante Network Latency
typ. 1.00 ms
Mains Input
1 x Neutrik powerCON-HC
Environmental
Ambient Temperature Limits
5 °C to +40 °C (+40 °F to +105 °F)
IEC Protection Class
Class I, grounded
Shipping
Weight
37.1 pounds
General
2Ω
1250W
2.7Ω
1250W
4Ω
2500W
8Ω
2500W
Low-Z Mode, ref.1 Khz
32.0 dB, adjustable 20.0-44.0 dB
Direct Drive Mode
33.2/36.2/39.2/42.2 dB for 70/100/140/200 V
DIM 100 (3.15 Khz, 15 kHz)
<0.15%
IMD-SMPTE (60Hz, 7kHz)
<0.05%
Crosstalk (ref. 1 Khz, 12 Db Below Max, 8 Ω)
<-80dB
Damping Factor (20 Hz to 200 Hz, 8Ω)
>400
Connectivity
Analog Audio Input/Thru, Network, GPIO Control Port
Standby Mode
<18W
Sampling Rate
48 kHz/96 kHz, OMNEO/Dante synchronized
Signal Delay/Latency (analog in to Speaker Out, 48kHz/96kHz)
0.70ms/0.53ms
User EQ
2 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass and Notch; 2 filters of them with additional asymmetric filter type
User Delay
0 to 2000 ms per channel (units: µs, ms, s, cm, m, inches, feet)
Array EQ
filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, and All-Pass
Array Delay
0 to 500 ms per channel (units: µs, ms, s, cm, m, inches, feet)
Speaker EQ
10 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, Lo-Pass and All-Pass
Speaker X-Over
Hi-Pass, and Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth, 12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel
Speaker FIR
up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker Limiters
Peak Anticipation Limiter and RMS/TEMP Limiter per channel
Other Functions
Source Selection and Mix, Level, Mute, Polarity, Sine and Noise Generator, Pilot Tone Generator and Detection, Level Meters, Impedance Measurement and Load Monitoring
DSP Presets
1 Factory + 20 User
Speaker-Pool Presets
30 Speaker Settings
Source Supervision and Fallback
Pilot Tone supervision at Analog and OMNEO/ Dante inputs, switchover to alternative Source Selection
Front Panel Indicators
4 x status LEDs (POWER, STANDBY, FAULT, OMNEO)
Front Panel Operating Elements
3 buttons (UP, ENTER, DOWN)
Rear Panel Indicators
1x status LED (STATUS)
Rear Panel Operating Elements
mains switch
Protections
Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over-/Under voltage Protection
Cooling
front-to-rear, temperature controlled fans, supervised
Electromagnetical Environment
E1, E2, E3
Indicators
Display
black/white OLED 256 x 64 pixel

Why Choose SoundPro?

Since 1972, SoundPro has been the trusted source for audio, video, and lighting gear. Whether you're starting your AVL journey or are a seasoned professional, we're here to help you every step of the way.

Start Shopping

  • Certified Account Managers

    Our Account Managers, with 16+ industry certifications, are ready to find your solution.

  • Personalized Pricing

    We know every project is unique. Get a personalized quote anytime you need it

  • Fast Shipping & Local Pickup

    In stock items ship same day if ordered by 4pm CST. Pickup offered in Irving, TX.

  • Accountability from Real People

    We aim for a smooth, transparent experience by setting and sticking to clear expectations.

  • Easy Payments & Financing

    We accept all major credit cards and also offer financing through our partners.

1 2